Yes, the Curt Echo Brake controller # C51180 that you referenced does fit your 2017 Land Rover Discovery that has a factory 7-way. Basically this controller fits any vehicle that has a fully functional 7-way. As long as the trailer lighting circuits are functioning and the 12 volt accessory circuit is active this controller will work great. view full answer...
The Curt hitches like part # C13243 for the 2020 Land Rover Range Rover Sport require the stabilization strap part # 18050 with accessories because the Land Rovers are not designed to handle a lot of tongue weight and accessories like bike racks are considered all tongue weight which puts a lot of leverage on the setup.
Both the Draw-Tite Hitch part # 75229 and the Curt hitch will be recessed under the bumper because they install exactly the same. I have attached a video snip showing... view full answer...
I have a solution for you but you will need that part number you circled to find a replacement roof rack from Land Rover or online. We do not sell OEM parts. We do offer a roof rack that will fit your 2016 Land Rover LR4's factory installed tracks that run front to back. This rack is also compatible with the Thule SnowPack Extender Ski and Snowboard Carrier item # TH7325. It is the 2016 Land Rover LR4 Roof Rack by Rhino Rack. This Roof Rack Includes:
Rhino-Rack Vortex Aero Crossbars -... view full answer...
You didn't say how long of a hitch extender you need but the part # HE06 is 7 inches long and would help you get additional clearance for the etrailer cargo carrier part # e98874 to fold up like you are wanting. You should note that when you use a hitch extender like this you end up cutting the capacity of the hitch by 50 percent due to the increased leverage and movement created. view full answer...
Let's start with the hitch ball, and there is a 2" hitch ball with base just like the 2-5/16" Hitch Ball w/ Base # TVBB25 you mentioned, and for that you'd need the following part:
- 2" Hitch Ball w/ Base # TVBB2
As for the bracket kit; there is not one available without the foot. view full answer...
If your 2010 Land Rover Range Rover has the factory tow package then I recommend using the Tekonsha Prodigy P3 # 90195. This is one of the most reliable brake controllers that we have which is reflected in the massive amount of positive reviews left by customers.
The P3 is a proportional brake controller that will apply the brakes on your trailer at the same time and with the same intensity as the brakes in your vehicle. The best feature about this brake controller is the LCD screen that... view full answer...
There is one option for a roof rack that will fit your 2013 Land Rover Range Rover Sport that attaches to the factory track fixed mounting points on your vehicle. The rack is from Inno and consists of the following parts:
- Inno Aero Crossbars # INXB145-2
- Inno Through Feet for Aero Crossbars - Fixed Mounting Points # INXS350
- Custom Fit Kit # INTR112
I have added links below to instructions and a video review for you to check out as well. view full answer...
Of your two options the Rhino-Rack Pioneer Platform Rack with Fixed Mounting Points # JB0686 will be the lowest profile. Both options can carry up to 165lbs while moving, but the static weight of the Rhino Rack Pioneer Platform is around 900lbs. Perfect for a rooftop tent!
We have not test fit the Rhino-Rack Pioneer Platform on a 2016 Land Rover LR4, but if you did have clearance issues you can buy some extra spacers # LHS2PAIR to gain that clearance.
The ladder # RRRAFL is 91-1/2 inches... view full answer...
Yes, the BulletProof Hitches 2-Ball Mount # HD204 can be placed in the rise orientation allowing for a maximum 5-1/2" rise. With the mounting holes space 2" on center you will be able to place the ball height at 3-1/2" of rise to be very close to your trailer couplers height. view full answer...
I can tell you exactly how to find the correct ball mount for your 2014 Range Rover. What you'll want to do is make sure your Land Rover and trailer are each parked on level ground. Then measure from the ground to the top of the hitch receiver. Also measure from the ground to the bottom of your trailer's coupler.
If the hitch height is greater, you need a ball mount with drop. If the coupler height is greater, you'll need a ball mount with rise. You will also also want a draw bar with... view full answer...
The Curt # C59496 wiring harness is a universal-fit item that will work on any vehicle with a 12V wiring system, so it'll work great on your Land Rover LR2.
You will need to use the included circuit tester to locate the brake light circuit behind the vehicle tail light. Once this circuit is located it will be connected to the smaller red wire coming from the converter box.
Next, locate the left turn signal circuit and connect the yellow wire to that circuit. The green wire is then ran... view full answer...
According to page 221 on your owner's manual. A set of tire chains can only be installed on the rear wheels if they are 19" in diameter. They can however be installed on the front wheels if they are 20" in diameter. Per the manual, before using a set of tire chains on your 2010 Land Rover Range Rover Sport you must first disable the Dynamic Stability Control (DSC) system and not exceed 30 mph.
Therefore, I can only recommend that you use the Konig Premium Self-Tensioning Snow Tire Chains... view full answer...
The Tow Ready Adapter # 20142 is intended to work on a range of European import vehicles including your Land Rover LR3. It is not a vehicle brand-specific item.
According to my contact at TowReady this item should operate as intended on your LR3 to prevent low-current draw LED trailer lighting from triggering bad bulb error messages on your LR3's dash display. My contact has had no reports of issues with this item used in Land Rovers.
Before installing this adapter it is suggested that... view full answer...
If you have a Thule roof rack with lock core stamped 101 then the Replacement Key for Thule Racks and Carriers part # THKEYN101 will work. It looks like Thule made roof racks for Land Rover so this should work for that rack as well. view full answer...
Yes, the Stealth Hitches Hidden Rack Receiver item # SH63MR is a confirmed fit for your 2018 Land Rover Discovery. This is a custom fit receiver and when not in use completely hides the hitch. Keep in mind this receiver is only for carrying accessories so if you plan to tow a trailer you will need the towing kit with ball mount and trailer wiring harness item # SH99FR for your Stealth Hitches hitch receiver. This kit comes with a 2" ball and all necessary equipment to run your trailers... view full answer...
A trailer weight distribution/sway control (WD/SC) system is appropriate under a number of conditions, such as when the trailer weighs more than half the weight of the towing vehicle, when the vehicle headlights point upward when it is hitched, if steering and braking performance suffer or if there is rear-end sag in the vehicle. The linked article and video on WD/SC go into detail about these conditions.
Vehicles that have an automatic leveling system can still use WD/SC. The procedure... view full answer...
That is correct. If your 2020 Land Rover Discovery has the full sized spare it would have to be left off to install the Stealth Hitch part # SH97GR. One option would be to track down a smaller spare. view full answer...
I went ahead and checked, and there actually is not a fit kit available for your 2016 Land Rover LR4 and the Inno Dual Angle Ski and Snowboard Carrier # INTX726, unfortunately.
Instead, I recommend checking out the Inno Gravity Ski and Snowboard Carrier # INA951.
This ski and snowboard carrier will clamp directly to your factory roof rails and will give you the ability to transport 6 fat skis or 4 snowboards.
Additionally, this rack measures 56-3/4" fully expanded, 41-3/4" fully retracted,... view full answer...
Your 2007 Land Rover Range Rover does not have a direct plug and play wiring harness but there is a solution. I suggest the Wiring Harness # C59496. This harness has an upgraded circuit protected powered taillight converter to protect your Rover from electrical shorts. The kit includes all of the wiring, the converter box, quick splice connectors, and a circuit tester. Everything you need for installation. view full answer...
The Titan Chain Alloy Snow Tire Chains - Diamond Pattern - Square Link part # TC2326 does not fit a 225 tire. They fit the following tires sizes:
255/65-18
255/70-18
255/75-17
255/85-16
265/50-20
265/70-17
265/75-16
275/55-19
285/60-17
285/65-16
32x11.5-15
33x9.5-15
I would need to know the middle number to get you the correct chains. Normally the number is printed on the side of your trailer tire. view full answer...
Go To Results